TalkSwitch Release 4.10

Release 4.10.022 is an update for TalkSwitch VS, 48-CVA, 48-CA, and 24-CA products that introduces new options to expand and enhance your TalkSwitch system with the purchase of licensed add-ons. This release is intended only for use in the United States and Canada.

WARNING: This software must not be used, and is not supported, for TalkSwitch 48-NLS or TalkSwitch 24 units. This software must not be used, and is not supported, in other markets. The application of this software update to TalkSwitch 48-NLS or TalkSwitch 24 units, or units in use outside the United States and Canada invalidates any warranty, and may result in a situation where the product's original software may not be recoverable.

This update includes a new version of the TalkSwitch Configuration software bundled with new TalkSwitch firmware. Note: All units need to be updated with firmware version to take advantage of new features. Instructions for updating both the software and the firmware are included below.

Instructions for Installing Software Release

Step 1: From your present TalkSwitch software, use File > Save to File to store your current TalkSwitch configuration file to a convenient location on your PC, for future reference (if needed).

Step 2: Confirm that your present version of TalkSwitch software is 3.24.033 or later. From the TalkSwitch software, go to About TalkSwitch window. Software Version will be displayed in the left-center area of the window. If your system is equipped with 3.24.033 or later software, you should proceed to Step 3.

If you have TalkSwitch CA/CVA and/or VS models, and are using a version of TalkSwitch firmware older than 3.24.033, you will need to first upgrade to 3.24.033 software before installing 4.10.022: click here to download 3.24.033 software.

If you are using a TalkSwitch 48-NLS or TalkSwitch 24 model, DO NOT install this software update (see warning above).

Step 3: Download the 4.10.022 software. The download includes the software, firmware and documentation.

Step 4: Run the installer TSC401022.exe program. If a previous version of the software is installed, a dialog will pop-up and request to uninstall a previous version. Click 'Yes'.

Note: Your saved configuration files will not be removed.

Step 5: If you are updating from Release 3.24 or earlier, a confirmation dialog window will pop-up to ensure that you want to uninstall this product.

Select 'Yes'. This will remove the older version of the software. Note: Your saved configuration files will not be removed.

Step 6: The TalkSwitch Installation Wizard will appear. Click 'Next' to proceed.

Step 7: In order for the installer to load all necessary software for your products, two dialog windows will appear. On the first window select Next to proceed. TalkSwitch 24-CA owners may use the checkbox option to reduce the size of the installation.

On the next window specify the location on your PC to install the necessary software. The default location is recommended for most installations.

Step 8: The installation will then proceed. A progress display window will appear. When all files have been loaded, a final window will confirm that the installation has completed successfully.

Note: If the installation did not succeed, close the installer, ensure that the PC is running a fully-updated, compatible version of Windows, then re-try the installation.
If problems persist contact your TalkSwitch reseller, or the TalkSwitch Technical Assistance Center at 1.866.393.9960.

INSTRUCTIONS FOR UPDATING TO TALKSWITCH FIRMWARE REL 4.10

In order to take advantage of new features, you need to update the firmware of your TalkSwitch unit(s). This process will require that the system not be in use for approximately 3-15 minutes.

Step 1: Ensure TalkSwitch is connected to your PC or to the same LAN as your PC. Connection via Internet (IP) or Ethernet will result in the quickest update (For 24-CA use USB).

Note: TalkSwitch software may load or update a USB driver on your PC. If a "Found New Hardware Wizard" window appears, we recommend that you allow Windows Update to update your system with the latest driver software. This process should only occur once (if at all).

Step 2: Run the newly installed TalkSwitch Configuration software. When software establishes a connection with the TalkSwitch unit, a window will pop-up, informing you there is new firmware available. Click 'Update Now' to proceed with the update.

The configuration software will first retrieve your TalkSwitch configuration file and store it. During the update, your configuration file will be converted to be compatible with the new software and firmware while preserving your previous settings. The program will then update all required files with status information relayed at every step.

Step 3: Once complete, you will have the option to reboot the system now or if it's in use, to wait until all resources are locked down before the system reboots. Click 'Proceed' to continue.

A dialog will appear with a timer while the system(s) reboot.

When complete it will save the newly converted configuration file back to your TalkSwitch units, and open the new version of software. Please check your configuration settings to ensure all settings are correct.

Congratulations! Your TalkSwitch software and firmware updates are complete. Please take the time to review the documentation to take advantage of the new features and benefits of this release.

Home \| Products\| Where to Buy \| Support \| News & Events \| About Us \| Contact	Site Map \| Countries \| RSS Feed
Call Toll-Free in North America: 1.888.332.9322 ©2007 Centrepoint Technologies. TalkSwitch is a registered trademark of Centrepoint Technologies Inc. Prices and products on this web site are intended for North America only.